Results 1 to 9 of 9

Took delivery today

This is a discussion on Took delivery today within the General Tech and Discussions forums, part of the Can-Am Commander UTV Garage category; Only had time for a small ride, but this thing realy rips. The tranny clunk is very irritateing, almost seems like backlash in the transmission. Clutch engagement is not nearly ...


  1. #1
    Founding Member
    Join Date
    Sep 2010
    Posts
    69

    Default Took delivery today

    Only had time for a small ride, but this thing realy rips. The tranny clunk is very irritateing, almost seems like backlash in the transmission. Clutch engagement is not nearly as smooth as my outlander, a little jumpy trying to get it in back of my truck. I have a picture of it in my truck for those that didn't think it could be done but I have to figure out how to put it on here (not real great with these coputers). Did not notice any power loos in a hard corner but I am going to be conservative for a while, seemed a little squirly at high speed on a lose gravel road, I know the air presure is high in the tires so I need to get that down a bit. Any sugestions on tire pressue? Going on a big ride tomorrow so probably will not sleep tonite.

    By the way they were assembeling an X while I was doing my paper work.

  2. #2
    Sitting Idle
    Join Date
    Aug 2010
    Posts
    18

    Default

    Was the X sold?

  3. #3
    Founding Member
    Join Date
    Sep 2010
    Posts
    69

    Default

    There was 4 guys fighting over it.

  4. #4
    Sitting Idle Rhino Sparks's Avatar
    Join Date
    Sep 2010
    Location
    Sparks, Nevada
    Posts
    17

    Default

    Could you please run a tape to measure the actual width at the front tires? I would love to get it in my Tundra.

  5. #5
    Founding Member
    Join Date
    Sep 2010
    Posts
    69

    Default

    these are best I can get doing it myself.

    Front 57" wheels
    Rear 58.6" Wheels They are comletely on the tail gate.

    Max 63.5 " but this is 24" from the ground, so the wide spot is above the rail on my dodge.
    The bad part is the front bumper is over the rail too, makes it very close to back window. Will have to make some sort of stop.

  6. #6
    The Outlaw Ignore Amos Ignore Amos's Avatar
    Join Date
    Jul 2010
    Location
    Tucson, AZ
    Posts
    197

    Default

    What part of the country are you in Tom (or state) just trying to see where the X's are finally hitting...

    thanks for the update...going to go measure my small trailer to see how it'll fit.
    AVID OFFROAD RACING would like to thank our Sponsors!!!
    TURNKEY UTV-GBC Tires-MUZZY EXHAUSTS-BEARD SEATS-RIGID LIGHTS-RUGGED RADIOS, AIRDAM CLUTCHES, FACTORY UTV

  7. #7
    Founding Member
    Join Date
    Sep 2010
    Posts
    69

    Default

    I am 50 miles east of La CA.

    The X had s/n 0095

  8. #8
    Founding Member Xelvic's Avatar
    Join Date
    Sep 2010
    Location
    Tucson, Arizona
    Posts
    126

    Default

    Quote Originally Posted by wingshooter View Post
    I am 50 miles east of La CA.

    The X had s/n 0095
    Wow, with that VIN#, I would tend to believe the X's were made first. That goes against everything we've heard.
    "Make it idiot proof and someone will make a better idiot."

  9. #9
    Founding Member
    Join Date
    Sep 2010
    Posts
    69

    Default

    My XT s/n was 0459 I think it goes by model not overall. They both got to the dealer the same day.

Similar Threads

  1. Pictures of delivery day. 1000XT
    By Racermutt in forum CommanderTalk.com Member's Rides
    Replies: 20
    Last Post: 09-28-2010, 05:37 PM
  2. Spoke to Dealer today....
    By Ignore Amos in forum General Tech and Discussions
    Replies: 5
    Last Post: 09-15-2010, 02:37 PM
  3. Any Delivery Updates From Dealers?
    By dieselpowered in forum General Tech and Discussions
    Replies: 18
    Last Post: 08-18-2010, 11:06 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •